BLACK NOVEMBER −30% on all knives Only in November · no code · until 30 November · Free EU shipping from €79Shop the knives

Knife guide

How to Strop a Knife for a Razor-Sharp Edge: Leather, Newspaper or a Fine Stone

Samura whetstone #8000, a very fine finishing stone of 185 × 65 mm, standing on the base that comes in its SAMURA box

Here is how to strop a knife in one sentence: after sharpening, draw the edge backwards, spine leading, along a strip of leather, a folded newspaper or your finest whetstone, at the same angle you sharpened at, with almost no pressure, alternating sides for ten to twenty strokes each. Stropping does not grind a new edge. It removes the last traces of the burr and straightens the very apex, and that is what turns a sharp knife into a razor-sharp one.

If you have ever sharpened carefully and then watched the edge go dull after two onions, a leftover burr was probably to blame. A few minutes with a strop fixes that.

What stropping does, and what it doesn't

When you sharpen on a whetstone, the abrasive pushes a thin wire of steel over to the opposite side of the edge. That wire is the burr. Alternating light strokes on the stone remove most of it, but a fine remnant usually stays, folded over the apex. It feels sharp for a few cuts, then tears off and leaves a ragged edge behind. This is one of the main reasons knives lose sharpness so soon after sharpening.

Stropping drags the edge backwards over a surface that gives slightly. The surface pulls the burr off instead of folding it further, and it polishes the last few microns of the bevel so the apex is straight and clean. The result is an edge that bites into paper, tomato skin or chicken skin without any pressure.

What stropping cannot do is make a dull knife sharp. A strop removes almost no steel. If the edge is rounded, chipped or has lost its angle, no amount of stropping helps; it needs a stone first. Our guide on how to sharpen kitchen knives covers that part, from grit choice to raising the burr. Stropping is the step that comes after.

How to strop a knife step by step

  1. Finish sharpening properly. Raise a burr along the whole edge on one side, flip the knife and raise it on the other, then take it down with light alternating strokes on your finest stone. The less burr you leave, the less the strop has to do.
  2. Lay the strop flat. A strip of leather, a few layers of newspaper or a sheet of plain cardboard on the counter is enough. Hold it down firmly with your free hand, or clamp it, so it cannot slide.
  3. Set the angle. Hold the knife at the angle you sharpened at. SAMURA's product texts give a factory bevel of 15–17° for its steel knives, so that is where you start with a SAMURA blade. If anything, lift the spine a touch higher rather than lower. Too low and the strop only touches the shoulder of the bevel, not the apex.
  4. Stroke spine first. Place the heel of the blade on the strop with the edge facing away from the direction you are about to move. Draw the knife toward you, spine leading, from heel to tip in one smooth sweep. Never push the edge forward into leather or paper: it cuts in and ruins the strop and the edge.
  5. Use almost no pressure. The weight of the knife is close to enough. Heavy pressure makes the surface wrap around the apex and rounds it off, which is the opposite of what you want.
  6. Alternate sides. Lift the knife at the end of the stroke, flip it, and repeat on the other side. Ten strokes per side is a good start; twenty is plenty. Count them so both sides get the same treatment.
  7. Test on paper. Hold a sheet of printer paper by one corner and slice down through it. A stropped edge glides through silently. If it snags in one spot, strop a few more strokes with attention to that part of the edge. Never test sharpness with your thumb.

Strop materials: leather, newspaper, cardboard or a fine stone

You do not need to buy anything to strop a kitchen knife. The surface only has to be slightly yielding, clean and flat. The classic options behave a little differently.

Strop surface Effect on the edge Best for Watch out for
Bare leather (belt, scrap, strop) Removes the burr, light polish Regular upkeep of any steel knife Old belts may be dirty or carry grit; wipe them first
Leather with polishing compound Removes the burr and polishes the bevel visibly Thin Japanese-style blades, very hard steels Compound is a fine abrasive: too many strokes round the apex
Newspaper, folded a few times Removes the burr, mild polish from the ink and clay in the paper A quick strop at the end of every sharpening session Lay it on something flat, not on a towel
Plain cardboard Removes the burr Emergencies, camping, the back of a cereal box Printed or glossy board can leave residue
Very fine whetstone (#5000–#8000) Removes the burr and refines the edge with a trace of real abrasion Anyone who already sharpens on stones Keep the stone wet and the pressure feather-light

Leather is the traditional choice because it has just the right give. Newspaper works surprisingly well and costs nothing, so it is the easiest way to start. If you already own a fine finishing stone, you may not need a separate strop at all, which brings us to SAMURA's range.

When a fine whetstone does the same job

To be upfront: SAMURA sells no leather strop and no stropping compound. What it does sell is the fine end of the whetstone scale, and a very fine stone used with trailing, feather-light strokes does what a strop does, with the bonus of a tiny amount of real sharpening.

The Samura whetstone #8000 is the finest single stone in the whetstone collection. Its product text describes it as a very fine stone for the very end of a sharpening session that lets you polish the edge to a mirror-like finish without extra polishing aids. It measures 185 × 65 mm, is 19 mm thick, weighs 353 g and comes in a SAMURA box with a base that keeps it steady while you work. Soak it for 10–15 minutes before use and keep it wet.

If you would rather own one stone for fine sharpening and finishing, the combination whetstone #3000/#8000 puts both grits on one 185 × 65 × 32 mm block (534 g). Sharpen finely on the #3000 side, then turn it over and finish on #8000. There is also a single #5000 stone for finishing and polishing. For help choosing between them, see our whetstone grit guide.

To strop on a stone, keep the same angle, draw the edge spine first exactly as you would on leather, and use no more pressure than the weight of the knife. Five to ten alternating strokes on #8000 after your normal sharpening remove the burr and leave an edge most people would call razor-sharp. If holding the angle is the hard part, SAMURA's sharpening angle holder sits on the spine of the blade and keeps the tilt constant with smooth ceramic guides that do not scratch the stone.

Stropping vs honing vs sharpening

The three words get mixed up, which is why people strop knives that need sharpening, or sharpen knives that only need honing.

Step Tool What it does How often
Sharpening Whetstone, diamond stone, electric sharpener Removes steel and cuts a fresh apex Every few weeks to months, depending on use
Stropping Leather, newspaper, fine stone Removes the burr and polishes the apex after sharpening At the end of every sharpening session, and as a touch-up between
Honing Honing rod (ceramic or steel) Realigns an edge that has rolled over in use Every few uses

A honing rod and a strop overlap more than people think. The Samura ceramic honing rod has a 254 mm ceramic rod, and its product text describes its job as polishing and adjusting the cutting edge the knife already has, at the factory bevel angle of 15–17°. That is close to what a strop does, only with an edge-leading stroke and a hard surface. For everyday upkeep between sharpenings, a rod is faster; for the final clean-up straight after the stone, a strop or an #8000 stone is gentler. Our comparison of a knife honer and a sharpener explains when a rod is enough and when it isn't.

Common stropping mistakes

  • Edge-leading strokes. Pushing the edge into leather or paper slices the strop and bends the apex. Always trail the edge.
  • Too much pressure. The surface wraps around the edge and rounds it. If your knife feels duller after stropping, this is almost always why.
  • Too low an angle. Stropping flat on the bevel polishes the shoulder and never reaches the apex. Match your sharpening angle or go a degree higher.
  • Dozens of strokes. After twenty per side you are no longer removing the burr, only rounding the edge, especially with compound.
  • A dirty strop. Grit, dust or dried food on the surface scratches the bevel. Wipe leather clean and use fresh newspaper.
  • Stropping instead of sharpening. If the knife will not slice paper after a proper strop, the edge has lost its geometry. Go back to the stone.

Which knives to strop, and which to skip

Every plain-edged steel kitchen knife benefits, from chef's knives and santokus to paring and boning knives. Thin, hard Japanese-style blades gain the most, because their fine apex shows the difference between a clean edge and a burred one most clearly.

There are three exceptions. A single-bevel knife is stropped on the beveled side only, with just a couple of light strokes on the flat back to lift the burr, the same way you finish it on the stone. Serrated knives cannot be stropped in the normal way: the scallops never touch a flat surface, so follow our guide to sharpening serrated knives instead and only wipe the flat back lightly over the strop. And ceramic blades are a different material altogether: leather and paper do nothing to zirconia, and only diamond abrasives sharpen it, as explained in our post on how to sharpen a ceramic knife.

Stropping FAQ

How do you strop a knife for a razor-sharp edge?

Sharpen first, then draw the edge spine first along leather, folded newspaper or a #5000–#8000 whetstone at your sharpening angle, with almost no pressure, ten to twenty alternating strokes per side. Test on paper and stop as soon as it slices cleanly.

Does stropping sharpen a dull knife?

No. Stropping removes the burr and aligns the apex of an edge that has just been sharpened; it removes almost no steel. A dull or chipped edge needs a whetstone before any strop will help.

How often should you strop a kitchen knife?

Always at the end of a sharpening session, and then whenever the knife starts to drag slightly but still cuts, often once a week in a busy kitchen. When stropping no longer brings the bite back, it is time to sharpen.

Do you need stropping compound?

Not for kitchen knives. Bare leather or newspaper removes the burr well. Compound adds polish and suits very hard, thin blades, but it also rounds the edge faster if you overdo the strokes, so use it sparingly if at all.

Knife guide